SSTV mode information
compiled by G3ZLS
[ Home ] [ Principles ] [ RGB Modes ] [ YUV Modes ] [ Feedback ]

YUV Modes

The YUV modes have much in common with techniques used in analogue broadcast television systems. These modes are somewhat more complicated than the RGB modes, but they take advantage of two simple physiological facts:

  • Light receptors in the human eye are more sensitive to light intensity (rod cells) than to colour (cone cells).
  • The eye is most sensitive to the green part of the spectrum but is less sensitive to reds and relatively insensitive to blue colours.

To take advantage of this, the largest part of the available time is devoted to light intensity information, called luminance, derived from the red, green and blue components, which enables a high resolution black-and-white image to be reconstructed.  The colour information is transmitted in two additional low resolution colour difference components, called chrominance or chroma information, which effectively apply a colour wash to the black-and-white image.

The main drawback of YUV transmission using SSB equipment is that mis-tuning of the signal causes a significant hue shift (to green or magenta) instead of simply producing a slightly lighter or darker image as with the RGB modes. Nevertheless, the high stability of modern radio equipment together with the tuning aids which can be incorporated in the decoding software mean that tuning accuracy is no longer the problem it once was.

Encoding

The basic YUV SSTV system was pioneered by Robot Research, Inc. of the USA. According to the technical information given in the handbook for the Robot 1200C scan converter, the luminance signal Y is computed as follows:

Y = 0.3R + 0.59G + 0.11B

The two chrominance signals are computed by:

U = B - Y     and     V = R - Y

Although a complete line still requires three components the advantage lies in the fact that the U and V components can be sent at lower resolution without significant loss of image quality. This can be done in two ways. Firstly, the U and V components can be sent faster than the Y components (less time per pixel). Secondly, each of the U and V components can be averaged over two lines.

The following table gives values calculated for different coloured pixels according to the above formulae:

WHITE BLACK
R = 255 Y = 255 R = 0 Y = 0
G = 255 U = B-Y = 0 G = 0 U = B-Y = 0
B = 255 V = R-Y = 0 B = 0 V = R-Y = 0
YELLOW AQUA
R = 255 Y = 227 R = 0 Y = 179
G = 255 U = B-Y = - 227 G = 255 U = B-Y = 76
B = 0 V = R-Y = 28 B = 255 V = R-Y = - 179

It will therefore be seen that the luminance component varies between 0 and 255. The Y signal is therefore transmitted in the normal way with black corresponding to 1,500 Hz and white at 2,300 Hz. However, the chroma signals can be both positive and negative. In order to allow for this, 1,900 Hz is taken to represent a value of zero, with higher frequencies representing positive values and lower frequencies representing negative values.  The range of values allocated to each of the three components is given in the following table.

Frequency Hz Y U (B-Y) V (R-Y)
2,300 255 227 179
1,900 127 0 0
1,500 0 - 227 - 179

Decoding

The Y, U and V values obtained from the received line data can be written to a line buffer.  Reconstructing the colour pixels requires reading the corresponding Y, U and V values from appropriate positions in the buffer and reconstructing the original RGB values for each pixel.  Calculating the red and blue values is relatively simple:

R = V + Y     and     B = U + Y

Retrieving the green values involves a slightly more complex calculation:

G = Y - 0.5V - 0.186U

EXAMPLE: To reconstruct an aqua colour pixel from the YUV values in the above table:

R = - 179 + 179 = 0

G = 179 - (0.5 x - 179) - (0.186 x 76) = 179 + 90 - 14 = 255

B = 76 + 179 = 255

22 January 2008